ReframeReprojector

Reprojects feature coordinates from one coordinate system to another in Switzerland, using the Reframe library from the Federal Office of Topography (swisstopo).

Jump to Configuration

Typical Uses

Reprojecting features when explicitly using the Reframe library is desired

How does it work?

The ReframeReprojector receives raster, vector, or point cloud features and reprojects their coordinates from one coordinate system to another, using the swisstopo GeoSuite Reframe library.

It handles typical planimetric and altimetric reference frame changes for Switzerland. The following Swiss reference frames are supported:

Planimetric

Plane coordinates LV03 (CH1903)
Plane coordinates LV95 (CH1903+)

Altimetric

National levelling network LN02 (levelled heights)
National height network LHN95 (orthometric heights, CHGeo2004)
Ellipsoidal heights (Bessel)

See Local Swiss reference frames at swisstopo for more information.

To perform a reference frame change, select the Source and Destination Planimetric Reference Frame and/or Source and Destination Altimetric Reference Frame as required.

The Source and Destination reference frames can be the same or blank, allowing for planimetric-only or altimetric-only transformation.

Usage Notes

FME has a Workspace Parameter, Reprojection Engine, that may be set to either FME (CS-Map) or Esri. This transformer will override this parameter setting.
The Reprojector provides similar functionality, and will use the default library (CS-Map or Esri) set in FME. It supports some Swiss coordinate systems, but will not use the Reframe library.

Working With Coordinate System Transformers

FME inherently supports coordinate system transformations and reprojections.

Coordinate System Support and Reprojection

Coordinate systems generally have a name and a definition, and the syntax of that definition can vary greatly between both spatial data formats and other coordinate system libraries. Custom and local coordinate systems can also be defined in FME, further complicating matters. For in-depth information, see the Working With Coordinate Systems documentation.

Reprojections are generally done with the FME Reprojection Engine, which is based on the CS-Map coordinate system library. This default can be overridden on a per-workspace basis, using the Workspace Parameters > Translation > Reprojection Engine parameter, and set to Esri. Where appropriate, FME will use the Esri Reprojection Engine if it is selected there, with or without an Esri product being installed.

Coordinate System Support

These transformers perform various coordinate system-related tasks, but do not reproject the data.

CoordinateSystemDescriptionConverter	Looks up coordinate system names and definitions between FME’s internal format and common third-party and open source representations, storing the results as an attribute.
CoordinateSystemExtractor	Retrieves the name of the feature's assigned FME coordinate system into an attribute.
CoordinateSystemRemover	Removes the coordinate system from features, without modifying geometry or coordinates.
CoordinateSystemSetter	Assigns a specified coordinate system to features, without modifying geometry or coordinates.
LocalCoordinateSystemSetter	Assigns a specified local coordinate system to features, without modifying geometry or coordinates.

Coordinate System Reprojection

Different coordinate system libraries (engines) not only contain coordinate system definitions, they also have unique reprojection algorithms. FME’s generic reprojection transformers, in the first table below, default to using the FME (CS-Map) library.

A selection of other libraries is also available, some of which are specific to certain areas of the world or software platforms.

Inherent reprojections, as in a workspace with different input and output coordinate systems selected, default to using the FME (CS-Map) library.

If you are reprojecting explicitly with a transformer in the workspace, using library-specific transformers is recommended. In the case of CsmapReprojector versus the Reprojector (with default engine), the library may be identical, but the CSMapReprojector handles vertical coordinate calculations whereas the Reprojector does not.

Generic Reprojection Transformers

		Library
AttributeReprojector	Reprojects x and y coordinates stored as attributes from one coordinate system to another.	FME (default) or Esri
CommonLocalReprojector	Reprojects one or more features to a local coordinate system centered on the bounding box containing all features.	FME (default) or Esri
ReprojectAngleCalculator	Converts a given angle from one coordinate system to another.	FME (default) or Esri
ReprojectLengthCalculator	Converts a given length from one coordinate system to another.	FME (default) or Esri
Reprojector	Reprojects feature x and y coordinates from one coordinate system to another.	FME (default) or Esri

Library-Specific Reprojection Transformers (Recommended)

		Library (External Links)
CsmapAttributeReprojector	Reprojects x, y, and optionally z coordinates stored as attributes from one coordinate system to another using the CS-MAP library.	CS-Map
CsmapReprojector	Reprojects feature x, y, and optionally z coordinates from one coordinate system to another using the CS-Map library.	CS-Map
EsriReprojector	Reprojects feature coordinates from one coordinate system to another using the Esri reprojection library.	Esri
GridInQuestIIReprojector Great Britain Northern Ireland Republic of Ireland	Reprojects feature coordinates from one coordinate system to another using the Grid InQuestII engine from Ordnance Survey, for use in Great Britain, Ireland, and Northern Ireland.	Grid InQuestII
GtransAttributeReprojector Sweden	Reprojects coordinates stored as attributes from one coordinate system to another using the Gtrans reprojection engine from the National Land Survey of Sweden (Lantmäteriet).	Gtrans
GtransReprojector Sweden	Reprojects feature coordinates from one coordinate system to another using the Gtrans reprojection engine from the National Land Survey of Sweden (Lantmäteriet).	Gtrans
PROJAttributeReprojector	Reprojects coordinates stored as attributes from one coordinate system to another using the PROJ library.	PROJ
PROJReprojector	Reprojects feature coordinates from one coordinate system to another using the PROJ library.	PROJ
ReframeReprojector Switzerland	Reprojects feature coordinates from one coordinate system to another in Switzerland, using the Reframe library from the Federal Office of Topography (swisstopo).	REFRAME

Configuration

Input Ports

Output Ports

Parameters

General

Source Planimetric Reference Frame	Specify the horizontal (x,y) reference frame of the input features. Choices include: <blank> - No horizontal reference frame Automatic (read from feature) - checks for an equivalent of either LV03 or LV95 LV03 (CH1903.LV93_swisstopo) LV95 (CH1930Plus_1.LV95/01)
Destination Planimetric Reference Frame	Select a horizontal (x,y) reference frame for the output features. Choices include: <blank> - No horizontal reference frame Automatic (opposite of source) - chooses the inverse (LV03 or LV95) of the input LV03 (CH1903.LV93_swisstopo) LV95 (CH1930Plus_1.LV95/01)
Source Altimetric Reference Frame	Specify the vertical (z) reference frame of the input features. Choices include: <blank> - No vertical reference frame LN02 (usual heights) LHN95 (orthometric heights) Bessel 1841 (ellipsoidal heights)
Destination Altimetric Reference Frame	Select a vertical (z) reference frame for the output features. Choices include: <blank> - No vertical reference frame LN02 (usual heights) LHN95 (orthometric heights) Bessel 1841 (ellipsoidal heights)

Raster

Cell Size

Select a method for resizing cells:

Stretch Cells	The cell size of the raster will be adjusted to maintain the same number of rows and columns in the reprojected raster as there were in the input raster.
Square Cells	The number of rows and columns as well as the spacing will be changed to maintain approximately the same cell ground area and form square cells where the horizontal and vertical cell sizes are equal.
Preserve Cells	Like Square Cells, this option will change both the number of rows and columns and the spacing to maintain cell ground area, but will also try to preserve the original cell aspect ratio, taking into account any warping caused by the reprojection.

Interpolation Type

Select a method for interpolating reprojected cell values:

Nearest Neighbor	The simplest and fastest method. Values are copied from the nearest cell.
Bilinear	Calculates a weighted average, adjusted for distance, from the four (4) nearest cells.
Bicubic	Calculates a weighted average, adjusted for distance, from the sixteen (16) nearest cells.
Average 4	Calculates a simple average from the four (4) nearest cells. Similar to Bilinear and is useful for numeric rasters such as DEMs.
Average 16	Calculates a simple average from the sixteen (16) nearest cells. Similar to Bicubic and is useful for numeric rasters such as DEMs.

Editing Transformer Parameters

Using a set of menu options, transformer parameters can be assigned by referencing other elements in the workspace. More advanced functions, such as an advanced editor and an arithmetic editor, are also available in some transformers. To access a menu of these options, click beside the applicable parameter. For more information, see Transformer Parameter Menu Options.

Defining Values

There are several ways to define a value for use in a Transformer. The simplest is to simply type in a value or string, which can include functions of various types such as attribute references, math and string functions, and workspace parameters. There are a number of tools and shortcuts that can assist in constructing values, generally available from the drop-down context menu adjacent to the value field.

How to Set Parameter Values

Using the Text Editor

The Text Editor provides a convenient way to construct text strings (including regular expressions) from various data sources, such as attributes, parameters, and constants, where the result is used directly inside a parameter.

Text Editor

Using the Arithmetic Editor

The Arithmetic Editor provides a convenient way to construct math expressions from various data sources, such as attributes, parameters, and feature functions, where the result is used directly inside a parameter.

Arithmetic Editor

Conditional Values

Set values depending on one or more test conditions that either pass or fail.

Parameter Condition Definition Dialog

Content

Expressions and strings can include a number of functions, characters, parameters, and more.

When setting values - whether entered directly in a parameter or constructed using one of the editors - strings and expressions containing String, Math, Date/Time or FME Feature Functions will have those functions evaluated. Therefore, the names of these functions (in the form @<function_name>) should not be used as literal string values.

Content Types

String Functions	These functions manipulate and format strings.
Special Characters	A set of control characters is available in the Text Editor.
Math Functions	Math functions are available in both editors.
Date/Time Functions	Date and time functions are available in the Text Editor.
Math Operators	These operators are available in the Arithmetic Editor.
FME Feature Functions	These return primarily feature-specific values.
FME Parameters	FME and workspace-specific parameters may be used.
Creating and Modifying User Parameters	Create your own editable parameters.

Dialog Options - Tables

Transformers with table-style parameters have additional tools for populating and manipulating values.

Table Tools

Row Reordering

Enabled once you have clicked on a row item. Choices include:

Add a row
Remove a row
Move current row up one
Move current row down one
Move current row to top
Move current row to bottom

Cut, Copy, and Paste

Enabled once you have clicked on a row item. Choices include:

Cut a row - delete and copy to clipboard
Copy a row to the clipboard
Paste a row from the clipboard

Cut, copy, and paste may be used within a transformer, or between transformers.

Filter

Start typing a string, and the matrix will only display rows matching those characters. Searches all columns. This only affects the display of attributes within the transformer - it does not alter which attributes are output.

Import

Import populates the table with a set of new attributes read from a dataset. Specific application varies between transformers.

Reset/Refresh

Generally resets the table to its initial state, and may provide additional options to remove invalid entries. Behavior varies between transformers.

Note: Not all tools are available in all transformers.

Reference

Processing Behavior	Feature-Based
Feature Holding	No
Dependencies	swisstopo Reframe provided with FME
Operating System Restrictions	Windows only
Aliases
History

FME Community

The FME Community is the place for demos, how-tos, articles, FAQs, and more. Get answers to your questions, learn from other users, and suggest, vote, and comment on new features.

Search for all results about the ReframeReprojector on the FME Community.

Examples may contain information licensed under the Open Government Licence – Vancouver and/or the Open Government Licence – Canada.