Autodesk AutoCAD DWG/DXF Reader Parameters

The schema will be generated using layers in the source dataset as FME feature types.

The schema will be generated using all the possible AutoCAD geometry types as FME feature types. This list is set by the reader capability and is not limited to geometries which occur in the given source dataset.

The schema will be generated using both the layers and entities in the source dataset. The layers will be used to create FME feature types as in the Group by Layer Name selection; however, the attributes of all the entities belonging to a layer will be accumulated and also added to the FME feature type for that layer. For Extended Entity Data attributes to appear, the reader parameter Read Interpreted Extended Entity Data must be selected.

When selected, this parameter explodes blocks and return the entities that form the components of the block as separate features.

When the reader resolves blocks, it outputs a feature for each of the AutoCAD entities that are part of the block definition. The original insert is not output. This results in the full graphical representation of the block transferred through FME, but the exact insertion point of the block is lost.

Each block member feature is given the attribute autocad_block_number which is set to the same value for each block so that the features comprising each block may be combined in subsequent processing. Arbitrary deep block nesting is permitted, however, the autocad_block_number attribute is only updated for each block at the outermost level.  By default, all block members will be on the same layer as that of the original block.

Usual AutoCAD-to-AutoCAD translation setting: Not selected

Specifies how the reader sets the feature type of block component entities when resolving (or exploding) insert entities. This parameter applies only if Explode Blocks into Entities is checked.

When the reader resolves blocks, it outputs a feature for each of the AutoCAD entities that are part of the block definition. If this parameter is checked, all block members will be on the same layer-based feature type as that of the original block. If this parameter is unchecked, the block members will appear on their respective layer-based feature types.

This parameter is useful when resolving components and using a layer-based schema, and you want block component features to share a layer-based feature type. To change the layer information on the component features to match their layer-based feature type, use the Use Block Layer Information for Components parameter.

Usual AutoCAD-to-AutoCAD translation setting: Not selected

Specifies how the reader sets the layer information attributes of the block component entities when resolving (or exploding) insert entities. This parameter applies only if Explode Blocks into Entities is selected.

When the reader resolves blocks, it outputs a feature for each of the AutoCAD entities that are part of the block definition.

If this parameter is checked, all block members will have the same layer information as that of the original block. If this parameter is unchecked, the block members will have the layer information of their respective layers.

Examples of layer specific attributes are autocad_layer, autocad_layer_hidden, and autocad_layer_color. This parameter also affects related symbology attributes such as autocad_lineweight and autocad_color which may have ByLayer values.

Usual AutoCAD-to-AutoCAD translation setting: Not selected

When selected, the reader adds the insert point location as attributes to the block component entities when resolving (or exploding) inserts entities.

When the reader resolves blocks, it outputs a feature for each of the AutoCAD entities that are part of the block definition. The original insert is not output, but this parameter allows the insert location to still be represented.

Each block member feature will include the attribute autocad_block_insert_[xyz].

Usual AutoCAD-to-AutoCAD translation setting: Not selected

If the parameter Explode Blocks Into Entities is selected, and this parameter is also selected, then the insert points of exploded blocks are output as point features.

Explode Selected Blocks: This parameter is a a space-delimited list of the block names that are to be exploded, and is processed only when Explode Blocks into Entities is selected.

Specifies whether the reader should return visible attributes as separate text features or whether they should be returned as attributes of an insert feature. When this option is selected, then each visible attribute is returned as a single text feature.

Note: Note: Multi-line attributes are represented as text strings with embedded line feed characters.

Usual AutoCAD-to-AutoCAD translation setting: Selected

Specifies whether the reader will explode the mtext entities into separate text entities. If selected, the resulting text features represent fragments of text with the same mtext properties such as style and location.

If not selected, the mtext entity will be read as a single text feature.

Usual AutoCAD-to-AutoCAD translation setting: Not selected

Determines whether polylines should have their elevation attribute treated as a Z coordinate (applies to light-weight polylines and 2D polylines).

AutoCAD-to-AutoCAD translation setting: This option should not be set when performing AutoCAD-to-AutoCAD translations as the elevations converted to Z coordinates when read in will not be converted back to elevation attributes when written out.

When selected, this parameter instructs FME to read the entities from the model space.

If this parameter and Read Selected Paper Spaces are both selected, entities from the model space and paper space may be read. These entities are from spaces that represent distinct views and may overlap or be greatly separated (which may reduce visibility during inspection).

Usual AutoCAD-to-AutoCAD translation setting: Selected

Specifies which paper spaces should be read if Read Paper Space is selected.

If this parameter and Read Model Space are both selected, entities from the model space and paper space may be read. These entities are from spaces which represent distinct views and may overlap or be greatly separated which may reduce visibility during inspection.

If multiple paper spaces are selected entities may overlap which may reduce visibility during inspection.

Usual AutoCAD-to-AutoCAD translation setting: Not selected

When selected, this parameter instructs FME to read a geometric representation of the layout border from a paper space.

Usual AutoCAD-to-AutoCAD translation setting: Not selected

When selected, this parameter instructs FME to read a geometric representation of model space entities as they are seen through a paper space viewport.

Note that each viewport in each paper space selected may require additional computation and processing time during read.

Usual AutoCAD-to-AutoCAD translation setting: Not selected

Determines whether FME will read the extended entity data associated with AutoCAD entities in the Interpreted representation. By default, FME will not read extended entity data in this representation. See Extended Entity Data for details on these representations.

Note: Note: When generating a workspace or adding a reader with the Group entities by option set to Attribute schema, setting this option is required to get Extended Entity Data on the schema.

Determines whether FME will read the extended entity data associated with AutoCAD entities in the List representation.

By default, FME will read extended entity data in this representation. See Extended Entity Data for details on these representations.

Determines whether FME will read the Attribute entity information commonly associated with Insert entities.

By default, FME will read extended entity data in this representation.

This information consists of the fme_attrib_info attributes as a structured list. This is the same information that can be added to features as attributes with the Read Visible Attributes as Text Entities, though in a list representation. See Inserts for details.

Instructs the AutoCAD Reader regarding reading of XRecord entries in the extension dictionaries of entities. These XRecord entries may become FME feature attributes accordingly.

If not selected (which is the default), any XRecord entries will not be read.

If selected, the XRecord data will become FME feature attributes similar to the list form of Extended Entity Data, but with attributes with names of the form autocad_xrecord_data*.

Use this parameter to expose Format Attributes in Workbench when you create a workspace:

• In a dynamic scenario, it means these attributes can be passed to the output dataset at runtime.
• In a non-dynamic scenario where you have multiple feature types, it is convenient to expose additional attributes from one parameter. For example, if you have ten feature types and want to expose the same attribute in each one, it is easier to define it once than it is to set each feature type individually in the workspace.

Using the minimum and maximum x and y parameters, define a bounding box that will be used to filter the input features. Only features that intersect with the bounding box are returned.

If all four coordinates of the search envelope are specified as 0, the search envelope will be disabled.

Select this parameter to remove any portions of exported features outside the area of interest.

The illustration below shows the results of the Search Envelope when Clip to Search Envelope is set to No on the left side and Yes on the right side.

• No: Any features that cross the search envelope boundary will be read, including the portion that lies outside of the boundary.
• Yes: Any features that cross the search envelope boundary will be clipped at the boundary, and only the portion that lies inside the boundary will be read. The underlying function for the Clip to Search Envelope function is an intersection; however, when Clip to Search Envelope is set to Yes, a clip is also performed in addition to the intersection.

Determines whether to resolve the entity's color, or keep it as ByLayer. When selected (which is the default), the autocad_color attribute will contain the actual color by value (an integer between 0 and 255 inclusive) therefore preserving the original attributes.

For example, if you have an entity on a "rivers" layer, with its color set to ByLayer, and the layer color set to "blue":

• If you select this option, then the autocad_color attribute will be set to "blue" (its equivalent integer value).
• If you do not select this option, then the autocad_color attribute will be set to ByLayer (an integer value of 256) and the components will all be assigned the same layer color.

Usual AutoCAD-to-AutoCAD translation setting: Not selected

Specifies whether or not to read hatches and MPolygons in a way that preserves their complex properties.

If this parameter is selected, the loops will be aggregated together as polygons, and ordered such that any enclosing loop will be stored before any enclosed loop. Attributes may be added to store polyline bulge arc information.

If this parameter is not selected, the loops of each hatch entity will be converted to areas and aggregated together, and polyline bulge arcs will be interpolated into lines.

Usual AutoCAD-to-AutoCAD translation setting: Selected

Specifies whether the reader should leave a raster unclipped and only store the clipping information as attributes, or whether it should apply the clipping.

• If selected, the raster will not be clipped and the clipping information may be retrieved from the feature attributes, this allows clipped raster features to pass through FME with no loss of data.
• If not selected (default), clipped rasters being read will have their clipping information applied, and anything outside the clipping bounds will be lost.

Usual AutoCAD-to-AutoCAD translation setting: Selected

Specifies whether or not to resolve (explode) dimensions into their individual pieces.

If selected, each geometric piece of the dimension will be output as a separate feature, as well as a non-geometric autocad_dimension_def feature.

If not selected, an aggregate containing all the pieces of the original dimension will be output (i.e., an autocad_dimension).

Usual AutoCAD-to-AutoCAD translation setting: Not selected

Determines how multi-line entities are read. If unchecked, multi-line geometry is constructed of lines containing only the explicit vertexes of the base line and the relative vertexes of additional lines. When checked, additional evaluation of multi-line properties is performed, which may result in additional vertexes and gaps in the geometry. The evaluated geometry form is a more complete geometric representation of a multi-line entity, but cannot be written without loss by the AutoCAD Writer.

When selected, the AutoCAD Reader, in addition to vectorizing the splines, stores the spline coefficients as attributes.

See the description of Splines for the attribute names used to store the spline definition.

Usual AutoCAD-to-AutoCAD translation setting: Selected

When selected, the AutoCAD reader doesn’t vectorize the Polyline and LWP Line Bulges but rather just stores the coefficients in the attribute autocad_bulge.

In addition, when specified, this parameter allows the creation of autocad_start_width and autocad_end_width attributes to represent the width properties of Polyline and LWP entities.

Usual AutoCAD-to-AutoCAD translation setting: Selected only when performing AutoCAD-to-AutoCAD translations

Instructs FME to ignore the user-defined coordinate system of the file being read. By default, FME applies the UCS when reading the coordinate data.

Usual AutoCAD-to-AutoCAD translation setting: Always selected

Specifies whether a zero-length arc should be converted into a point feature (that is, autocad_point).

If the feature becomes a point, it will still retain all the attributes it had while it was an arc.

Usual AutoCAD-to-AutoCAD translation setting: Never selected

Determines whether or not AutoCAD groups will be read. By default, FME will not read groups.

Determines whether FME will read AutoCAD entities that represent External References. By default, FME will not read External References.

If you select this option, the AutoCAD Reader will add additional attributes describing the layer properties for the layer of each feature. These include autocad_layer_linetype, autocad_layer_color, and autocad_layer_lineweight.

The reader will output all the block definitions at the beginning of the translation before any other features are output. After the blocks are output, the rest of the translation is run without the blocks being resolved.

This value overrides the value specified by Explode Blocks Into Entities.

When selected, all features that are part of a block definition have the attribute autocad_block_definition, with the value of the attribute being the name of the block which they are a component.

When selected, specifies whether a zero-length arc should be converted into a point feature (that is, autocad_point).

If the feature becomes a point, it will still retain all the attributes it had while it was an arc.

Usual AutoCAD-to-AutoCAD translation setting: Never selected

Specifies whether the reader will ignore all features on the frozen layers.

If selected, features located on the frozen layers are not read from the input dataset.

If not selected, the features are read from the frozen layer.

Select this parameter if you have an Esri World file (*.wld) that you want FME to use when determining the coordinates for features in your dataset.

FME will search the folder of the dataset for a file with the same name as your dataset but with a .wld extension. If it cannot find a file with that name, it will then look for the file esri_cad.wld within the dataset folder. If either of those files exists, FME will use the information in the files to translate the coordinates of the features in the dataset to their new geospatial coordinates.

If the files cannot be found, then the translation will continue, using the coordinate information found in the dataset, without performing any additional transformation.

Determines whether FME will attempt to read a graphical representation of Proxy entities which are placeholders for certain unsupported objects. By default, FME will read Proxy Graphics.

Determines whether FME will attempt to read certain AutoCAD System Variables that are stored within the drawing. By default, FME will not read Drawing System Variables.

When reading DXF files, this parameter instructs the reader to use the specified DXF header file as the header for the file being read. This option is used in situations where organizations produce headerless DXF files to save storage space.

Specify the full pathname to the DXF header file.

Note: If this parameter is specified for a DWG file, the translation is terminated with an error.