GridInQuestIIReprojector

Reprojects feature coordinates from one coordinate system to another using the Grid InQuestII engine from Ordnance Survey, for use in Great Britain, Ireland, and Northern Ireland.

Jump to Configuration

Typical Uses

Reprojecting features when explicitly using the Grid InQuestII engine is desired

How does it work?

The GridInquestIIReprojector receives raster, vector, or point cloud features and reprojects their coordinates from one coordinate system to another, using Ordnance Survey’s Grid InQuestII engine.

Its library allows you to transform coordinates between ETRS89 (WGS84) and the national coordinate systems of Great Britain, Northern Ireland and the Republic of Ireland.

The following coordinate systems are supported:

ETRS89 (WGS84)
- UTM Zone 29N
- UTM Zone 30N
- UTM Zone 31N
- Cartesian
- Geodetic
OSGB36 British National Grid
Irish Grid
Irish Transverse Mercator

Two vertical datums are available, for Irish systems only:

Malin Head
Belfast

This transformer always reprojects from the source coordinate system to the destination coordinate system, tagging the features with the destination coordinate system on output.

Any coordinate system set on the input features is ignored - it is not able to read coordinate systems from incoming features.

Usage Notes

FME has a Workspace Parameter, Reprojection Engine, that may be set to either FME (CS-Map) or Esri. This transformer will override this parameter setting.
The Reprojector provides similar functionality, and will use the default library (CS-Map or Esri) set in FME. It supports some of the same coordinate systems, but will not use the Grid InQuestII library.

Working With Coordinate System Transformers

FME inherently supports coordinate system transformations and reprojections.

Coordinate System Support and Reprojection

Coordinate systems generally have a name and a definition, and the syntax of that definition can vary greatly between both spatial data formats and other coordinate system libraries. Custom and local coordinate systems can also be defined in FME, further complicating matters. For in-depth information, see the Working With Coordinate Systems documentation.

Reprojections are generally done with the FME Reprojection Engine, which is based on the CS-Map coordinate system library. This default can be overridden on a per-workspace basis, using the Workspace Parameters > Translation > Reprojection Engine parameter, and set to Esri. Where appropriate, FME will use the Esri Reprojection Engine if it is selected there, with or without an Esri product being installed.

Coordinate System Support

These transformers perform various coordinate system-related tasks, but do not reproject the data.

CoordinateSystemDescriptionConverter	Looks up coordinate system names and definitions between FME’s internal format and common third-party and open source representations, storing the results as an attribute.
CoordinateSystemExtractor	Retrieves the name of the feature's assigned FME coordinate system into an attribute.
CoordinateSystemRemover	Removes the coordinate system from features, without modifying geometry or coordinates.
CoordinateSystemSetter	Assigns a specified coordinate system to features, without modifying geometry or coordinates.
LocalCoordinateSystemSetter	Assigns a specified local coordinate system to features, without modifying geometry or coordinates.

Coordinate System Reprojection

Different coordinate system libraries (engines) not only contain coordinate system definitions, they also have unique reprojection algorithms. FME’s generic reprojection transformers, in the first table below, default to using the FME (CS-Map) library.

A selection of other libraries is also available, some of which are specific to certain areas of the world or software platforms.

Inherent reprojections, as in a workspace with different input and output coordinate systems selected, default to using the FME (CS-Map) library.

If you are reprojecting explicitly with a transformer in the workspace, using library-specific transformers is recommended. In the case of CsmapReprojector versus the Reprojector (with default engine), the library may be identical, but the CSMapReprojector handles vertical coordinate calculations whereas the Reprojector does not.

Generic Reprojection Transformers

		Library
AttributeReprojector	Reprojects x and y coordinates stored as attributes from one coordinate system to another.	FME (default) or Esri
CommonLocalReprojector	Reprojects one or more features to a local coordinate system centered on the bounding box containing all features.	FME (default) or Esri
ReprojectAngleCalculator	Converts a given angle from one coordinate system to another.	FME (default) or Esri
ReprojectLengthCalculator	Converts a given length from one coordinate system to another.	FME (default) or Esri
Reprojector	Reprojects feature x and y coordinates from one coordinate system to another.	FME (default) or Esri

Library-Specific Reprojection Transformers (Recommended)

		Library (External Links)
CsmapAttributeReprojector	Reprojects x, y, and optionally z coordinates stored as attributes from one coordinate system to another using the CS-MAP library.	CS-Map
CsmapReprojector	Reprojects feature x, y, and optionally z coordinates from one coordinate system to another using the CS-Map library.	CS-Map
EsriReprojector	Reprojects feature coordinates from one coordinate system to another using the Esri reprojection library.	Esri
GridInQuestIIReprojector Great Britain Northern Ireland Republic of Ireland	Reprojects feature coordinates from one coordinate system to another using the Grid InQuestII engine from Ordnance Survey, for use in Great Britain, Ireland, and Northern Ireland.	Grid InQuestII
GtransAttributeReprojector Sweden	Reprojects coordinates stored as attributes from one coordinate system to another using the Gtrans reprojection engine from the National Land Survey of Sweden (Lantmäteriet).	Gtrans
GtransReprojector Sweden	Reprojects feature coordinates from one coordinate system to another using the Gtrans reprojection engine from the National Land Survey of Sweden (Lantmäteriet).	Gtrans
PROJAttributeReprojector	Reprojects coordinates stored as attributes from one coordinate system to another using the PROJ library.	PROJ
PROJReprojector	Reprojects feature coordinates from one coordinate system to another using the PROJ library.	PROJ
ReframeReprojector Switzerland	Reprojects feature coordinates from one coordinate system to another in Switzerland, using the Reframe library from the Federal Office of Topography (swisstopo).	REFRAME

Configuration

Input Ports

Output Ports

Parameters

Coordinate Systems

Source Coordinate System	Specify the coordinate system of the input features. Choices include: ETRS89 / UTM Zone 29N ETRS89 / UTM Zone 30N ETRS89 / UTM Zone 31N ETRS89 Cartesian ETRS89 Geodetic OSGB36 / British National Grid Irish Grid Irish Transverse Mercator
Source Coordinate System Version	When Source Coordinate System is one of the following: OSGB36 / British National Grid Irish Grid Irish Transverse Mercator specify the version, either: 2002 or 2015
Destination Coordinate System	Select the coordinate system for the output features. Choices include: ETRS89 / UTM Zone 29N ETRS89 / UTM Zone 30N ETRS89 / UTM Zone 31N ETRS89 Cartesian ETRS89 Geodetic OSGB36 / British National Grid Irish Grid Irish Transverse Mercator
Destination Coordinate System Version	When Destination Coordinate System is one of the following: OSGB36 / British National Grid Irish Grid Irish Transverse Mercator specify the version, either: 2002 or 2015
Vertical Datum (Irish systems only)	If required, select a vertical datum. Choices include: Malin Head Belfast This parameter is for the regions between Northern Ireland and the Republic of Ireland.

Raster Parameters

Interpolation Type

Select a method for interpolating reprojected cell values:

Nearest Neighbor	The simplest and fastest method. Values are copied from the nearest cell.
Bilinear	Calculates a weighted average, adjusted for distance, from the four (4) nearest cells.
Bicubic	Calculates a weighted average, adjusted for distance, from the sixteen (16) nearest cells.
Average 4	Calculates a simple average from the four (4) nearest cells. Similar to Bilinear and is useful for numeric rasters such as DEMs.
Average 16	Calculates a simple average from the sixteen (16) nearest cells. Similar to Bicubic and is useful for numeric rasters such as DEMs.

Cell Size

Select a method for resizing cells:

Stretch Cells	The cell size of the raster will be adjusted to maintain the same number of rows and columns in the reprojected raster as there were in the input raster.
Square Cells	The number of rows and columns as well as the spacing will be changed to maintain approximately the same cell ground area and form square cells where the horizontal and vertical cell sizes are equal.
Preserve Cells	Like Square Cells, this option will change both the number of rows and columns and the spacing to maintain cell ground area, but will also try to preserve the original cell aspect ratio, taking into account any warping caused by the reprojection.

Tolerance (cells)

Sets the tolerance, in cells, for approximating reprojected cell locations.

Using the default value of 0.0, every cell will be reprojected.

If a value greater than 0.0 is specified, some cell locations will be approximated. The difference between an approximated cell location and the true cell location should be at most the tolerance value.

For example, if a value of 0.5 is specified, each approximated cell location should be maximum one-half of a pixel away from its true location. Increasing the Tolerance value may improve performance.

Editing Transformer Parameters

Transformer parameters can be set by directly entering values, using expressions, or referencing other elements in the workspace such as attribute values or user parameters. Various editors and context menus are available to assist. To see what is available, click beside the applicable parameter.

How to Set Parameter Values

Defining Values

There are several ways to define a value for use in a Transformer. The simplest is to simply type in a value or string, which can include functions of various types such as attribute references, math and string functions, and workspace parameters.

Using the Text Editor

The Text Editor provides a convenient way to construct text strings (including regular expressions) from various data sources, such as attributes, parameters, and constants, where the result is used directly inside a parameter.

Text Editor

Using the Arithmetic Editor

The Arithmetic Editor provides a convenient way to construct math expressions from various data sources, such as attributes, parameters, and feature functions, where the result is used directly inside a parameter.

Arithmetic Editor

Conditional Values

Set values depending on one or more test conditions that either pass or fail.

Parameter Condition Definition Dialog

Content

Expressions and strings can include a number of functions, characters, parameters, and more.

When setting values - whether entered directly in a parameter or constructed using one of the editors - strings and expressions containing String, Math, Date/Time or FME Feature Functions will have those functions evaluated. Therefore, the names of these functions (in the form @<function_name>) should not be used as literal string values.

Content Types

String Functions	These functions manipulate and format strings.
Special Characters	A set of control characters is available in the Text Editor.
Math Functions	Math functions are available in both editors.
Date/Time Functions	Date and time functions are available in the Text Editor.
Math Operators	These operators are available in the Arithmetic Editor.
FME Feature Functions	These return primarily feature-specific values.
FME Parameters	FME and workspace-specific parameters may be used.
Creating and Modifying User Parameters	Create your own editable parameters.

Dialog Options - Tables

Table Tools

Transformers with table-style parameters have additional tools for populating and manipulating values.

Row Reordering

Enabled once you have clicked on a row item. Choices include:

Add a row
Remove a row
Move current row up one
Move current row down one
Move current row to top
Move current row to bottom

Cut, Copy, and Paste

Enabled once you have clicked on a row item. Choices include:

Cut a row - delete and copy to clipboard
Copy a row to the clipboard
Paste a row from the clipboard

Cut, copy, and paste may be used within a transformer, or between transformers.

Filter

Start typing a string, and the matrix will only display rows matching those characters. Searches all columns. This only affects the display of attributes within the transformer - it does not alter which attributes are output.

Import

Import populates the table with a set of new attributes read from a dataset. Specific application varies between transformers.

Reset/Refresh

Generally resets the table to its initial state, and may provide additional options to remove invalid entries. Behavior varies between transformers.

Note: Not all tools are available in all transformers.

For more information, see Transformer Parameter Menu Options.

Reference

Processing Behavior	Feature-Based
Feature Holding	No
Dependencies	Ordnance Survey Grid InQuestII engine, provided with FME
Operating System Restrictions	Windows only
Aliases
History

FME Community

The FME Community has a wealth of FME knowledge with over 20,000 active members worldwide. Get help with FME, share knowledge, and connect with users globally.

Search for all results about the GridInquestIIReprojector on the FME Community.

Examples may contain information licensed under the Open Government Licence – Vancouver, Open Government Licence - British Columbia, and/or Open Government Licence – Canada.